cherrywhe.blogg.se - Tubulatr key pin depth gauge printable

Tubulatr key pin depth gauge printable install#
Tubulatr key pin depth gauge printable software#
Tubulatr key pin depth gauge printable code#
Tubulatr key pin depth gauge printable password#

Then there was a list: Joe has key number one, Mary has key number two, and so on. The number one may mean that several copies of this key were made originally, and they were numbered, "1, 2, 3, 4" and so on. "Do Not Duplicate" is a very common stamp put there in the usually vain hope that folks won't get the key copied. "M" often stands for "Master Key," but not always.

Tubulatr key pin depth gauge printable code#

Question: I found the key saying brass key 438 - 4904 M on the other side it says Do Not Duplicate with a one in the left corner where does this key go?Īnswer: 438-4904 does not correspond to any blind code number or key blank number that I know of or can find. Often cabinet locks will have the blind code stamped on the face of the lock, next to the keyway, so one can look at the number on the key and match it up with the number on the lock. If the code is published in a codebook or other resource, it will allow a locksmith with access to the resource to cut a key from that code. What could this key belong to?Īnswer: The small size probably indicates the key to a cabinet lock, though there are some screen door locks that take a small key. Question: I have a small silver key with the letters "CCP" on one side and AG45 on the other side. What might it belong to?Īnswer: It is not enough to go on, really, but it sounds like a room or suite number in a hotel or high rise building. Question: I have a key with the number 615. Keys cut on a Y11 blank usually fit some kind of cabinet lock.

What does that mean?Īnswer: Y11 is a key blank number. For example, you could say the bitting on this key is written "bow to tip".Īnswer: LL24 could be a keyset number in a very large grand master key system, or it could be a key code number. It's used to identify the order of a bitting.

Tip: You can find the tip at the opposite end of the key from the bow.

If a key has no cuts, it is not called a key. Listed, these depth numbers comprise the bitting of the key. 213" (two hundred thirteen thousandths of an inch) on a particular key brand. For example, a number one (1) cut may be. These depths are numbered according to their size in thousandths of an inch.

Cuts: In order to make a standard key, you need to cut material away to specific depths to accommodate the dimensions of the tumbler that is inside the lock.

Blade: The blade is the business end of the key and is where the cuts that correspond to the key's bitting are located.

On certain types of keys, the stop is located at the tip (end) of the key rather than the bow. Distances are measured starting at the stop to locate the cuts.

Stop: Located next to the bow on most keys, the stop keeps the key from going too far into the lock.

Bow/head: The bow works as the handle you use to hold and turn the key.

To understand the numbers and letters, you need to know the different parts that make up a key.

Tubulatr key pin depth gauge printable password#

Open the email attachment and give it to the engineer - the password to open the email attachment will be the user ID you use to sign in to the MOT testing service.Photo and artwork Tom Rubenoff The Anatomy of a Key Select ‘Request a key’ under ‘Change and connect equipment’.įollow the instructions to create and send the key to your email address.Ĭheck your email to find your key - make sure your email address is correct in the MOT testing service as the key will be emailed to this email address. Go to your ‘Vehicle testing station’ page. The key will not work at another testing station and only works on one piece of equipment.

Tubulatr key pin depth gauge printable install#

When the engineer is on-site and ready to install your equipment you need to request a key and give it to them.

Tubulatr key pin depth gauge printable software#

You need a software code (called a ‘key’) to connect equipment to the MOT testing service.

13-pin Euro trailer socket wiring testers.

Other types of equipment do not yet connect to the service. This rule does not apply to any current equipment you have, unless you need to replace it.